Colormatic 2k High Speed Primer Filler in Aerosol

(1)

  1. Complete Your Purchase
  2. Product information
  3. Specifications
  4. Product reviews
  5. Comparable products
Product information

Colormatic 2K Filler and primer at the same time

ColorMatic 2K hi-speed primer is universally applicable to all metallic surfaces such as steel, galvanized steel and aluminium. It offers excellent adhesion and corrosion protection and is very fast drying: 1 h (20 ° C). It is perfect for sanding, wet and dry. It is also solvent resistant

Available in 2 sizes

The Colormatic 2K High Speed Primer is available in a small aerosol of 200ml for when you only need to spray only a small part and also in a 500ml spray can for large surfaces.

Quality and properties

  • Filler and primer at the same time
  • Long pot life
  • Very fast drying time
  • Very good flow
  • Universal applicable for polished old paintwork and metal surfaces
  • Best to use 200 ml can to avoid surplus
  • Simple, time-saving application
  • Good adhesion to bare steel, galvanized steel and aluminium 

Physical and chemical data

  • Basis of binder: Acrylic
  • Colour: grey
  • Smell: solvent
  • Efficiency: Depending on consistance and colour of the ground: 400 ml are sufficient for 1,5 m²
  • Substrate: bare metal cleaned and sanded, zinc-coated metal cleaned and sanded, Aluminium cleaned and sanded, PE-Putty cleaned and sanded, plastic substrates should be pre-treated with ColorMatic 1K Plastic Adhesive
  • Temperature resistance: to 80°C
  • VOC-value: 114,2g
  • Pot life: 24 h at least

Using instructions

  1. Before use, carefully read and observe the warning texts on the label!
  2. Clean surface with ColorMatic silicone remover, then sand Old paintwork has to be cleaned and sanded 2-3 coats, 40 to 50µ Leave to dry for approximately three minutes between coats
  3. Ready to sand after about 45 min (20 ° C) or 30 min (60 ° C)
  4. Ready to recoat wet-on-wet after 20 minute drying time

Mixing A components with hardener:

  • Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring.
  • This will release the knife, which will penetrate the wall of the aluminium cartridge.
  • The cartridge will then rotate 360 °, be completely open and release the hardener.
  • Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio.
  • Shake can vigorously for 2 minutes
  • Carry out spray test
  • For professional use only Wear an appropriate respirator (recommended type A2/P3)

Hints concerning application

  • For smoothing over small unevenness, you can apply the ColorMatic 2K Hi-Speed primer filler up to a layer thickness of approx. 100 µ.
  • For best full drying results, we recommend working with several thin spray applications and a flash off time between the spray passes of approx. 3 minutes.
  • When stored at cool temperatures, the 2K Hi-Speed primer filler may also be used for several days following activation.
  • Allow to heat to room temperature prior to use (approx. (approx. 20°).
Full product information

Specifications

SKU conf_cmp-2k_primer-filler
Paint component 2K (2-component)
Brand MoTip
Contents 200ml + 500ml.
Packaging per stuk
All specifications

Product reviews

5/5

Based on 1 review

Write your review
Easily sprayable and covers super
Very good breeder/primer. Builds up nice layers, dries quickly and has good shear.
Nozzle settings are ideal.
Benny |
Translated from Dutch
Comparable products